“Sarmalep T/3” adhesive composition has high adhesive properties and vapor permeability; it is highly elastic and durable.

“Sarmalep T/3” adhesive composition is gradually added to pure water and mixed thoroughly manually or mechanically until obtaining lump-free consistency. Stir the mix again after approximately 10 minutes. Now the mix is ready for use. The prepared mix preserves its qualities during 1.5-2 hours, depending on temperature and humidity.

Spread the adhesive pointwise or continuously over a plate surface with a trowel, when attaching warmth-keeping jacket plates (see M1-99 to Construction Norms and Regulations 3.03.01-87). The area of adhesive joint should not be less than 40% out of the total area of glued plates. Use a toothed trowel when applying a protective and reinforcing layer. Use a smoothing trowel when fixing a net and smoothing a surface (see M1-99 to Construction Norms and Regulations 3.03.01-87). The preparation and application temperature is +5% …+30°C.

“Sarmalep 3” adhesive mix has high adhesive properties, crack growth resistance and vapor permeability; it is highly elastic and durable.

The adhesive mix is used for a protective and reinforcing layer in “TERMOSHUBA” heat-insulating system; in cases of absolute necessity it can also be used for gluing of insulation plates to mineral surfaces. It also can be used for facing with ceramic tiles or stone; and installing leveling layers over different mineral substrates.

Use a toothed trowel for a protective and reinforcing or leveling layer. Use a smoothing trowel, when fixing a net or smoothing a surface (see ÒÊÏ 45-3.02-24-2006). The preparation and application temperature is +5°Ñ …+30°Ñ. The exposed surface should be protected from the direct sunlight, wind, rain and other adverse environmental conditions during the work phase and 24 hours after it is completed.

“Sarmalep M/Ï” adhesive composition has advanced adhesive properties, vapor permeability, elasticity and durability.

The dry mix shall be of positive temperature before adding it to water. Add “Sarmalep M/Ï” dry mix into warm pure water (the temperature of water shall be about 30°Ñ) and mix it properly manually or mechanically until obtaining lump-free consistency. Stir the mixture again in approximately 3 minutes. Now it is ready for use. The prepared mix preserves its qualities during 20-60 minutes, depending on wind speed and temperature.

Spread the adhesive pointwise or continuously over a plate surface with a toothed trowel, when attaching warmth-keeping jacket plates (see M1-99 to Construction Norms and Regulations 3.03.01-87). The area of adhesive joint should not be less than 40% out of the total area of glued plates. Use a toothed trowel for the protective and reinforcing layer. Use a smoothing trowel for net fixing and surface smoothing (see M1-99 to Construction Norms and Regulations 3.03.01-87). The preparation and application temperature is -12°C… +10°C.

“SARMALEP Ï” adhesive composition has advanced adhesive properties and vapor permeability; it is highly durable.

The adhesive mix is used in “TERMOSHUBA” system for gluing insulation plates made of mineral wool or polystyrene foam to mineral substrates. It can also be used for tiling with ceramic tiles and making leveling layers over different mineral substrates.

The adhesive mix is spread pointwise or continuously with a toothed trowel over a plate surface, when attaching warmth-keeping jacket plates (see ÒÊÏ 45-3.02-24-2006). The area of adhesive joint should not be less than 40% out of the total area of glued plates. The preparation and application temperature is +5°C …+30°C.

“SARMALIT” plaster mix has advanced adhesive properties; it is highly elastic, durable and frost resistant.

“Sarmalit” plaster mix is gradually added to pure water and is mixed thoroughly manually or mechanically until obtaining lump-free consistency. Stir the mixture again in approximately 15 minutes. Now it is ready for use. The prepared mix needs to be utilized during 1-1.5hours. Water consumption depends on temperature, humidity and the desired consistency of the mix. Prevent the plaster from wind, rain and other adverse conditions during performing of works and drying of the plaster.

The mix is spread with a metal spatula or a trowel over a wall; after that smooth a surface with the help of a roller until obtaining the desired surface finish. It is also possible to apply the mix directly with a roll. In this case you need to add more water to the mixture. Do not add water to the mixture while performing the works. The preparation and application temperature is +5°C …+30°C.

The plaster is used for leveling brick and concrete walls for further finishing (including finishing before installation of “TERMOSHUBA” insulating system). The plaster can also be used for repairing of surfaces made of cement or cement-lime plaster. It is an excellent foundation for decorative thin-layer plasters. It can be used for indoor and outdoor works.

“SARMALIT HM/HMM” plaster mix has advanced adhesive properties; it is highly elastic and durable.

“SARMALIT HM/HMM” plaster mix is gradually added to pure water and is mixed thoroughly manually or mechanically until obtaining lump-free consistency. Stir the mixture again in approximately 5 minutes. Now it is ready for use. The prepared mix needs to be utilized during 1.5-2hours. Water consumption depends on temperature, humidity and the desired mix consistency.

The mix is spread evenly onto the wall manually or mechanically; after spreading the wall surface should be smoothed with a metal spatula. Prevent the mix from quick drying. The preparation and application temperature is +5°Ñ …+25°Ñ.

The plaster is used for leveling brick and concrete walls for further finishing (including finishing before installation of “TERMOSHUBA” insulating system). The plaster can also be used for repairing of surfaces made of cement or cement-lime plaster. It is an excellent foundation for decorative thin-layer plasters. It can be used for indoor and outdoor works

“Sarmalit HMM” plaster mix has advanced adhesive properties; it is highly elastic and durable.

Spread the mix evenly onto the wall manually or mechanically; after spreading the mix, smooth the wall surface with a metal spatula. Do not add water to the mix while performing works. Preparation and application temperatures are 8°Ñ … +10°Ñ. In case you would like to finish the surface or apply the additional layers of decorative compositions over “Sarmalit HMM” plaster, you need to warm the leveled surface up to positive temperature, until hoar-frost which appeared on the surface during the process of the material hardening disappears. This process is essential as the hoar-frost may prevent safe adhesion between the layers.

The plaster mix is used for high-quality decorative outdoor and indoor plastering over even mineral substrates. It also can be used as the finishing layer in TERMOSHUBA insulating system

“Sarmalit”-Premium plaster mix has advanced adhesion and frost resistance properties; it is highly elastic, durable and aesthetic.

The mix is spread evenly onto the surface (2.5mm thick) with the help of a metallic trowel. Do not add water to the mix while performing works. Preparation and application temperature is +5°Ñ…+25°Ñ. Prevent the exposed surfaces from the direct sunlight, wind, rain and other adverse conditions while performing works and 24 hours after.

The plaster mix is used for high-quality decorative outdoor and indoor plastering over even mineral substrates. It is also used as the finishing coat in “TERMOSHUBA” insulating system.

“Sarmalit” plaster mix is distinguished for its advanced adhesive properties; it has high elastic, durable, frost resistant and aesthetic properties.

The mix is spread evenly onto the surface (about 2.5mm thick) with the help of a metallic trowel. After approximately 10-15 minutes polish the surface with a plastic trowel until you get the desired surface finish. Do not add water to the mix while performing works. Preparation and application temperature is +5°Ñ …+25°Ñ. Prevent the exposed surfaces from the direct sunlight, wind, rain and other adverse conditions while performing works and 24 hours after.