|
Shaped objects: heat-shrinking sleeves, pipe bends, and piers (saddles). |
“SarmatTermoEngineering” construction company (subsidiary of “Sarmat” holding company) supplies all the range of insulated with polyurethane foam shaped objects covered with polyethylene or galvanized sheath and fulfils order of selected items for pre-insulated heat pipeline according to the customer’s specification.
Shaped objects for system completion of pre-insulated pipelines:
|
IN AUTUMN 2005 “SARMATTERMOENGINEERING” CONSTRUCTION COMPANY (SUBSIDIARY OF “SARMAT” HOLDING COMPANY) WAS THE FIRST IN THE REPUBLIC OF BELARUS TO LAUNCH THE BREAK-THROUGH PRODUCTION OF HEAT-SHRINKING SLEEVES FOR PRE-INSULATED PIPELINES! |
|
Heat-shrinking sleeves
manufactured by
“SarmatTermoengineering”
 |
|
| |
Benefits: |
 |
Manufactured in the Republic of Belarus |
| |
There are no analogous products in the Republic of Belarus |
| |
Their physical-mechanical properties are better than those of products produced by outside manufacturers |
| |
They are manufactured in compliance with the unique technology on the basis of high-strength modified polyethylene resistant to the influence of ultraviolet radiation which helps to avoid spontaneous sleeve shrinkage |
|
It is not allowed to remove protective polyethylene film from heat-shrinking sleeves before starting the process of heat insulation and waterproofing of welded joints. |
|
|
Nominal sizes of heat-shrinking sleeves: |
| Outer diameter of PI-pipe mantel, mm |
Inside diameter of sleeve, mm |
Sleeve wall thickness, mm |
Sleeve length, mm |
| 90 |
103 |
2,2 |
600 |
| 110 |
125 |
2,5 |
600 |
| 125 |
140 |
2,5 |
600 |
| 140 |
156 |
3,0 |
600 |
| 160 |
177 |
3,0 |
600 |
| 200 |
218 |
3,2 |
600 |
| 225 |
244 |
3,5 |
600 |
| 250 |
269 |
3,9 |
600 |
|
|
Bends
 |
|
|
|
Bend is a part of pipeline used for changing pipeline direction at an angle.
|
|
Bend |
|
|
Return bend |
|
|
Welded bend |
|
“SarmatTermoEngineering” construction company (subsidiary of “Sarmat” holding company) manufactures pre-insulated bends with various standard angles 15˚, 30˚, 45˚, 60˚, 75˚, 90˚. Pre-insulated bends can be manufactured with polyethylene and galvanized sheath. |
|
|
|
Piers
 |
|
|
|
Piers are devices used for installing pipeline in ready-to-work position and for load transfer from the pipeline to the basement or load-carrying structure.
|
|
Pre-insulated fixed pier |
|
|
Sliding pier |
|
Fixed pier is a special prefabricated element encased during installation work. Pre-insulated fixed piers are manufactured with polyethylene and galvanized sheath. |
|
|
|
PI-tees
 |
|
|
|
PI-tees are used for branching pipelines.
|
|
Straight tee |
|
|
Angle tee |
|
|
Parallel tee |
|
“SarmatTermoEngineering” construction company (subsidiary of “Sarmat” holding company) manufactures pre-insulated tees with polyethylene and galvanized sheath. |
|
|
|
Shaped parts manufactured by “SarmatTermoEngineering” construction company (subsidiary of “Sarmat” holding company) are supplied with wires for remote operation monitoring system which are laid inside the polyurethane foam insulation layer.
All practical questions of designing PI - pipeline systems are covered in “Sarmat” Ltd. publications:
“Recommendations for PI -pipeline designing” |
“Catalogue of pre-insulated pipes manufactured by “SarmatTermoEngineering” |
“Manual for system assemblage of pre-insulated with foam polyurethane pipelines of nominal size 25/90-630/800” |
“Manual for designing, assemblage and operating of ROM system” |
|
You can ask a question to get additional information about application of “SarmatTermoEngineering” pre-insulated pipeline systems. |
|
|